Benchtop Multimeters

• Designed to IEC 1010 standard
• Adapter allows access to hard-to-reach test points
• Tips are insulated to the point to prevent shorting of adjacent components

• 6.5 digit resolution
• Basic V DC accuracy of up to 0.0024%
• Dual display

• 6.5 digit resolution
• Basic V DC accuracy of up to 0.0024%
• Dual display

• 6.5 digit resolution
• Basic V DC accuracy of up to 0.0024%
• Dual display

This product has been discontinued by the manufacturer.

• 6.5 digit resolution
• Basic V DC accuracy of up to 0.0024%
• 100 µA to 10 A current range; with up to 100 pA resolution

• Broad range of functions; measuring volts; ohms and amps with a basic V DC accuracy of 0.015%
• Measure small currents with a resolution of up to 100 nA.
• Dedicated dc leakage current measurement

• Broad range of functions; measuring volts; ohms and amps with a basic V DC accuracy of 0.015%
• Measure small currents with a resolution of up to 100 nA.
• Six dedicated instrument setup keys to instantly select saved test configurations. Ideal for making routine measurements.

• Broad range of functions; measuring volts; ohms and amps with a basic V DC accuracy of 0.015%
• Measure small currents with a resolution of up to 100 nA.
• Basic V DC accuracy of 0.015%

• Tough molded plastic case with die-cut foam to hold and protect the 8845A or 8846A meter
•  Accessories and manual compartments
•  One-year warranty

• Pin tip jack at the adapter end is recessed for added insulation protection
• Adapter allows easy access to leads of through-hole IC’s
• Insulation at the tip fits between leads to prevent accidental shorting

• Plugs into USB device host port on the 8846A front panel
• Fully compliant with Universal Serial Bus Specification v2.0
• Dual LED indicates power and busy status

• Resistance Nominal 100 Ω
• Temperature coefficient 0.00385 Ω/Ω °C nominal
• Drift rate + 0.13 °C at 0 °C after 1000 hours at 300 °C

• 4-terminal shorting bar
• 4 mm banana terminals sized and oriented to short DMM input source and sense terminals
• Used to null out front end offsets or as required by the calibration procedure

• USB-to-serial-RS-232 interface adapter cable
•  Converts from standard DB 9-pin serial to USB 2.0
• Requires an available PC communications port

• Fluke 287 and 289 (Model FVF-SC2)
• Fluke 180 Series Digital Multimeters (Model FVF-SC2)
• Fluke 1653 Installation Testers (Model FVF-SC2)

• Fluke FVF-SC5 Flukeview Forms Basic Software
• For 8845/8846 Series Meters

FlukeView Forms supports the following meters:

• Fluke 287 and 289 (Model FVF-SC2)
• Fluke 180 Series Digital Multimeters (Model FVF-SC2)
• Fluke 1653 Installation Testers (Model FVF-SC2)

• Fluke Y8021 Shielded IEEE 488 Cable, 1M

• Cable length: 2m
• For use with Models for 8845A and 8846A

• 2 Small filler plate
• 1 Dual center mount
• 1 Rack mount tray

• 1 small filler plate
• 2 large filler plates
• 1 rack mount tray

• A digital multi-meter for a stationary workplace that can measure current, voltage and resistance, the digital multi-meter can also use two thermocouples to measure the temperature and also determine the conductivity.
• It can perform a variety of different measurement tasks. A direct connection to a PC can be established via the USB interface on the back of the digital multi-meter. The software from the digital multi-meter can then be used to carry out live analyzes using graphics and tables.
• Another special feature of the digital multi-meter is the PASS / FAIL function. With this function, target ranges for the measured values ​​can be set for each measuring function.