Demo
Add products to your Toolbox to save it for requesting a quote while you keep browsing for other products to complete your list.
Toolbox
PCE Instruments TG 300 Wall Thickness Gauge 0 to 600 mm
# TG 300
- The PCE-TG 300 is a wall thickness gauge with special sensors for various applications. In general, the wall thicknesses of all homogeneous materials can be measured with the PCE-TG 300.
- For damping or scattering materials such as plastic or cast a special sensor is available. An angled 90° sensor also enables measurements at hard-to-reach measuring points. The speed of sound can be set freely on the wall thickness gauge PCE-TG 300 and thus adapted to a wide variety of materials.
- The measured values are displayed directly on the easy-to-read TFT color display. Due to the internal memory, which can be read out via the optionally available software, different measuring points can be clearly stored.
- The PCE-TG 300 is a wall thickness gauge with special sensors for various applications. In general, the wall thicknesses of all homogeneous materials can be measured with the PCE-TG 300. For damping or scattering materials such as plastic or cast a special sensor is available. An angled 90° sensor also enables measurements at hard-to-reach measuring points. The speed of sound can be set freely on the wall thickness gauge PCE-TG 300 and thus adapted to a wide variety of materials.
- The measured values are displayed directly on the easy-to-read TFT color display. Due to the internal memory, which can be read out via the optionally available software, different measuring points can be clearly stored. The non-destructive ultrasound measuring method enables the measurement even on end products. Thanks to the Echo-Echo working mode, even coated workpieces can be measured.
- Large measuring range
- Various sensors available
- Battery operation
- Error and voids detection
- Internal measurement data memory
- Print via Bluetooth
| Measuring range | PE: pulse-echo mode 0.65 600 mm (steel) |
| EE: echo-echo mode 2.50 60 mm | |
| Accuracy | ± 0.04 mm H [mm] (<10 mm); ± 0.4% H [mm] (> 10 mm) |
| H refers to the material thickness of the workpiece | |
| Resolution | 0.1 mm / 0.01 mm / 0.001 mm (adjustable) |
| Measurable materials | Metals |
| Plastics | |
| Ceramics | |
| Epoxy resin | |
| Glass | |
| And all homogeneous materials | |
| Working modes | Pulse echo mode (fault and blower detection) |
| Echo-Echo mode (hiding layer thicknesses, eg paints) | |
| Calibration | Sound velocity calibration |
| Zeroing | |
| Two-point calibration | |
| View mode | Normal mode, Scan mode, Difference mode |
| Units | mm / inch |
| Data transfer | Print via Bluetooth / USB 2.0 |
| Storage | Non-volatile memory with 100 data groups with 100 data sets each |
| Operating time | Continuous operation 100 h |
| Automatic stand-by mode (adjustable) | |
| Automatic switch-off mode (adjustable) | |
| Power supply | 4 x AA battery 1.5V |
| Display | 320 x 240 pixels TFT LCD color display with brightness adjustment |
| Operating conditions | 0 50°C / 32 122°F, ≤ 80% RH not condensing |
| Storage conditions | -20 70°C / -4 158°F, ≤ 80% rh non-condensing |
| Dimensions | 185 x 97 x 40 mm / 7.3 x 3.8 x 1.6 in |
| Weight | 375 g / < 1 lb |
| Specification of the available sensors for wall thickness gauge PCE-TG 300 | |
| NO2 | |
| Frequency | 2.5 MHz |
| Diameter | 14 mm |
| Measuring range | 3 40 mm (steel) |
| 3 300 mm (steel) | |
| Minimum diameter of pipes | Not suitable for curved materials |
| Description | For damping / scattering materials (plastics, cast iron) |
| NO5 | |
| Frequency | 5 MHz |
| Diameter | 10 mm |
| Measuring range | 1 600 mm (steel) |
| Minimum diameter of pipes | 20 x 3 mm |
| Description | Normal measurement |
| NO5 / 90° | |
| Frequency | 5 MHz |
| Diameter | 10 |
| Measuring range | 1 600 mm (steel) |
| Minimum diameter of pipes | 20 x 3 mm |
| Description | Normal measurement |
| NO7 | |
| Frequency | 7 MHz |
| Diameter | 6 mm |
| Measuring range | 0.65 200 mm (steel) |
| Minimum diameter of pipes | 15 x 2 mm |
| Description | Or thin-walled or heavily curved pipes |
| HT5 | |
| Frequency | 5 MHz |
| Diameter | 12 mm |
| Measuring range | 1 600 mm (steel) |
| Minimum diameter of pipes | 30 mm |
| Description | For high temperatures (max 300°C / 572°F) |
| P5EE | |
| Frequency | 5 MHz |
| Diameter | 10 mm |
| Measuring range | PE: 2 600 mm, EE: 2.5 100 mm |
| Minimum diameter of pipes | 20 x 3 mm |
| Description | Normal measurement and EE test |
- 1 x Thickness gauge PCE-TG 300
- 1 x Sensor P5EE
- 1 x 100 ml coupling gel
- 1 x Transport case
- 4 x AA batteries
- 1 x User manual
Related Products
Explore More in Specialty Meters
Explore More in Testing Equipment
Provide us your contact detailsone of our product experts will contact you to discuss your needs or schedule a demonstration at a time that suits
Product selected: Model #
*Demonstrations can only be scheduled within the UAE