• Store Locator
  • Schedule a
    Demo
  • Add products to your Toolbox to save it for requesting a quote while you keep browsing for other products to complete your list.

    My
    Toolbox
  • Create a Requisition

    PCE Instruments ITE 50 Multifunction Installation Tester 1000V

    # ITE 50

    • The PCE-ITE 50 is a robust installation tester with a large 3.5″ TFT color LCD display.
    • The installation tester PCE-ITE 50 also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements.
    • With the low-resistance measurement of the PCE-ITE 50 installation tester, you can check grounding conductors, potential equalization rails and protective conductors for low impedance.
    PCE Instruments
    • PCE Instruments
    • ITE 50
    • The PCE-ITE 50 is a robust installation tester with a large 3.5″ TFT color LCD display. The installation tester PCE-ITE 50 also offers, in addition to the various measuring modes such as insulation resistance, grounding resistance, loop impedance, voltage, low-impedance measurement and RCD test with the camera function, the possibility of documenting suitable photos with the measurements. With the installation tester PCE-ITE 50, you can ensure that fixed installations are safely and correctly installed. Thanks to the dual display, the intuitive symbols and the high viewing angle, you can comfortably and quickly perform your measurements with the PCE-ITE 50 installation tester. With the low-resistance measurement of the PCE-ITE 50 installation tester, you can check grounding conductors, potential equalization rails and protective conductors for low impedance.
    • The measuring range for low-resistance measurement with the installation teser PCE-ITE 50 is in the range of 0 – 2000 Ω with a resolution of 0.001 – 1 Ω.  Probably the most important measurement of the installation tester PCE-ITE 50 is the measurement of insulation resistance. Electrical cables are placed under voltage during the insulation measurement in order to detect fault currents, Which generate material migration or heat. In most cases, these current faults are so minimal that they are not detected by protective devices and in the worst case they can lead to a fire. The installation tester PCE-ITE 50 can carry out installation measurement with a test voltage of 125V, 250V, 500V or 1000V. The load current is in each case 1 mA. The PCE-ITE 50 installation tester is independent of the mains supply. In order to bring all systems and circuits of a power supply system to a common potential (ground reference or potential reference) and to protect against short-circuit currents and overvoltages, the earthing resistor should be as low-impedance as possible. With a measuring range of 0 … 2000 Ω with a resolution of 0.01 … 1 Ω, the installation tester DT-6650 offers all the prerequisites for a meaningful measurement of the grounding resistance.
    • – 3.5″ color TFT LCD display
      – Loop resistance L-N, L-PE and N-PE
      – Adjustable FI test current
      – SD card and Bluetooth
      – Dual display
      – Good / bad FI test
      – Low Ohm measurement
      – Up to 1000V terminal voltage
    Voltage measurement
    Measuring range 80 to 500 V AC/DC
    Resolution 1 V
    Accuracy ± (2 % + 2 digits)
    Frequency measurement
    Measuring range 45 to 65 Hz
    Resolution 1 Hz
    Accuracy ±2 Hz
    Grounding measurement
    Measuring range 0.00 to 99.99 Ω, 100.0 to 999.9 Ω, 1000 to 2000 Ω
    Resolution 0.01 Ω, 0.1 Ω, 1 Ω
    Accuracy ± (2% + 30 digits), ± (2% + 6 digits), ± (2% + 6 digits)
    General specifications
    Power supply 8 x 1.2 to 1.5V AA batteries
    Operating time ca. 15 h
    Measurement category CAT III 600V
    Protection class IP 65
    Display 3.5″ TFT (320 x 240 Pixel)
    Operating environment 0 to 45°C, 0 to 95% rH, non condensing
    Measurements 24.2 x 10.5 x 14.5 cm
    Weight 1.56 kg / 3.4 lbs
    • 1 x Insulation Tester PCE-ITE 50
    • 1 x User manual

    Provide us your contact detailsone of our product experts will contact you to discuss your needs or schedule a demonstration at a time that suits

    Product selected: Model #







    *Demonstrations can only be scheduled within the UAE

    Sign up to stay in the know-how of our latest products, updates, special offers, and more.

    • Subscription Form