Demo
Add products to your Toolbox to save it for requesting a quote while you keep browsing for other products to complete your list.
Toolbox
PCE Instruments DPD-F1 Force and Weight Indicator 24V
# DPD-F1
- Digital display for strain gauges
- mV / V input
- 3 different measuring speeds
- Modular output cards are available
- 1/8 DIN panel mounting dimensions
- The built-in display is used to indicate the force and weight detected by force sensors and load cells with strain gauges. The output signal of the measuring cell is irrelevant because the DMS display makes it possible to display the correct weight in mV / V based on the set sensitivity. The DMS display shows the measured values on a 6-digit LED display. The measuring range could theoretically be between -199999 … 999999. Depending on the desired and adjusted scaling, a corresponding unit sticker can be affixed to the installation indicator.
- The DMS display can directly supply voltage to the connected measuring cell with strain gauges. The supply voltage can be selected between 5V and 10V. Depending on the voltage selected, up to 8 or 4 force or load cells can be connected to the DMS digital display. A special feature of this digital display for mV / V is the modular output concept. Different, changeable output cards are available depending on the application.
- Digital display for strain gauges
- mV / V input
- 3 different measuring speeds
- Modular output cards available
- 1/8 DIN panel mounting dimensions
- LED display
Technical specification for DMS display of the PCE-DPD-F series | |||
| Signal Input Range | Accuracy at 25°C | Sensitivity in mV / V at 5V | Sensitivity in mV / V at 10V |
| 0 … 100 mV DC | ± 0.05% of reading | 20 mV / V | 10 mV / V |
| 0 … 30 mV DC | ± 0.05% of reading | 6 mV / V | 3 mV / V |
| 0 … 20 mV DC | ± 0.05% of reading | 4 mV / V | 2 mV / V |
| 0 … 15 mV DC | ± 0.05% of reading | 3 mV / V | 1.5 mV / V |
| 0 … 10 mV DC | ± 0.05% of reading | 2 mV / V | 1 mV / V |
| 0 … 5 mV DC | ± 0.05% of reading | 1 mV / V | 0.5 mV / V |
| Maximum input voltage | 30V in all measuring ranges | ||
| Supply voltage measuring cells | 5V or 10V | ||
| Maximum current | 140-mA | ||
| Maximum number of measuring cells (with 350 Ohm measuring cells otherwise max. 140-mA) | 5V supply: 1 … 8 measuring cells 10V supply: 1 … 4 measuring cells | ||
| Display | 6-digit 7-segment LED display | ||
| Units (available to user) | g, kg, t, pcs, mg, lb, N, kN | ||
| Colour | Red | ||
| Character height | 14 mm | ||
| Display area | -199999 … 999999 | ||
| Decimal | Adjustable after each displayed digit | ||
| Under and Over range display | The display flashes | ||
| Measuring rate (adjustable) / response time | 16 Hz / 63 ms 50 Hz / 20 ms 60 Hz / 17 ms | ||
| Refresh rate display | 16 Hz | ||
| Electrical connections | Screw connections 1 … 2.5 mm² | ||
| Power supply | 85 … 265V AC / DC | ||
| Input | Max. 1 W without output cards Max. 4 W with output cards | ||
| Degree of protection | Front: IP65 | ||
| Assembly | Panel cut | ||
| Size panel cutout | 92 x 44 mm / 3.6 x 1.7 in | ||
| Dimensions | 96 x 48 x 91 mm / 3.7 x 1.9 x 3.6 in | ||
| Weight | About 150 g / < 1 lb | ||
| Operating temperature | 0 … 50°C / 32 … 122°F | ||
| Storage temperature | -20 … 70°C / -4 … 158°F | ||
| Heating time | About 15 minutes | ||
- 1 x Force and Weight Indicator PCE-DPD-F1
- 1 x Power supply terminal
- 1 x Strain gauge terminal
- 1 x Unit label
- 1 x User manual
Provide us your contact detailsone of our product experts will contact you to discuss your needs or schedule a demonstration at a time that suits
Product selected: Model #
*Demonstrations can only be scheduled within the UAE